Click here to download your YZ R owners manual. Click here to download your YZ TT1 owners manual. Click here to download your YZ T T1 owners manual. Click here to download your YZ V owners manual. Click here to download your YZ W W1 owners manual. Click here to download your YZ X1 owners manual. Click here to download your YZ X owners manual. Click here to download your YZ Y owners manual.
Click here to download your YZ Z owners manual. Click here to download your YZ S owners manual. Click here to download your YZRY owners manual.
Click here to download your YZ A owners manual. Click here to download your YZ AA1 owners manual. Click here to download your YZ B owners manual. Click here to download your YZ FB owners manual. This is an awesome site, very helpful. Would it be possible for you to let me know the password needed to edit the files so that I can remove the non-English pages? Thanks for all the available books I wanted to know if it was available manual Yamaha YZ Thank you.
My yz 2 stroke does only take ml then the oli comes out the oli level bolt Is this normal or not. This unit contains high-pressure nitrogen gas. Mishandling can cause explosion. Do not incinerate, puncture or open. Turn off the main switch after riding to avoid draining the battery. Use unleaded gasoline only. Coolant drain bolt Front brake lever Rear brake pedal Throttle grip Valve joint Radiator cap Air cleaner Fuel tank cap Drive chain Engine stop switch Shift pedal Kickstarter crank Oil level check window Fuel tank Page Consumer Information There are two significant reasons for knowing the serial number of your machine: 1.
When ordering parts, you can give the number to your Yamaha dealer for positive identification of the model you own. If your machine is stolen, the au In the conventional carburetor system, the air-fuel ratio of the mixture that is supplied to the combustionchamber is created by the volume of the intake air and the fuel that is metered by the jet used in the respective carburetor.
The pressure regulator maintains thefuel pressure that is applied to the fuel injector at only kPa 3. Accordingly,when the energizing signal from the ECU energizes the fuel injector, the fuel passage opens, causingthe fuel to be injected into the intake manifold only during the time the passage remains open.
Keep away from fire. We recommend to use Yamaha genuine parts for all replace- ments. Using the correct special tool will help prevent damage caused by the use of improper tools or improvised techniques.
The shape and part number used for the special tool differ by country, so two types are provided. Cap bolt ring wrench This tool is used to loosen or tighten YM, the damper assembly. Fork seal driver This tool is used when install the fork YM-A, Fuel pressure adapter This tool is used to attach the pres- YM, sure gauge. YM Valve guide installer This tool is needed to install the 5. Page Control Functions The clutch lever "1" is located on the left handlebar; it disengages or en- gages the clutch.
Pull the clutch lever Your Yamaha engine has been de- to the handlebar to disengage the signed to use premium unleaded gas- clutch, and release the lever to en- oline with a pump octane number gage the clutch.
When the engine starts running, 6. First, tighten the steering ring nut approximately 38 Nm 3. Torque specifications 6 mm for special components or assem- blies are included in the applicable sections of this book.
Main axle Oil check bolt Drive axle Scavenging pump Oil level check window Oil feed pump Cylinder head breather hose Fit the accessory coupler into Hose holder the connector to fasten it to the Radiator hose 3 bracket. Cable holder Pass the clutch cable through Clamp the lower guide only.
Fasten the fuel hose and fuel Front engine bracket Face the buckle of the plastic pump lead with the plastic band, Fuel injector coupler above the cover. Atmospheric pressure sensor Throttle body Route the spark plug wire be- coupler Clamp Fasten the engine stop switch Engine stop switch lead lead to the handlebar. Hose guide Route the brake hose to the Main harness front of the number plate. Page Regular Inspection And Adjustments If you are a doubt as to what intervals to follow in maintaining and lubricating your machine, consult your Yamaha dealer.
The service life of the parts varies sub- stantially according to the environment in which the machine runs e. Inspect and clean Change gasket. Before using this machine, check the following points. Do not remove the radiator cap "1", drain bolt and hoses when the engine and radiator are hot. Scald- Take care so that coolant does not ing hot fluid and steam may be splash on painted surfaces.
Apply the specified pressure. Attach: 1. Check: kPa 1. Apply: 4. Check: On the throttle cable end "a". Oil quantity: 2. Those place. Round off the last digit of the in- stalled pad number to the nearest increment. Tighten the bleed screw when the b. Tighten the locknut. Loosen the pad pin "2". Install the brake caliper "8" and c.
Remove the brake caliper "3" tighten the pad pin "9". Locknut: from the front fork. Replace: h. Install the brake pad "10" and pad 4. Remove: 6. Front B. There are marks 1. Loosen the locknut "1". Adjust: 1. Check: 1. Standard tire pressure: kPa 1.
Loosen the steering ring nut one turn. Retighten the steering ring nut us- ing the steering nut wrench. Avoid over-tightening. Steering ring nut final tightening : 7 Nm 0. Check the steering stem by turn- ing it lock to lock.
All control cable Page 81 If a problem occurs that is not listed in this manual or if the problem cannot be corrected by the procedures provided in this manual, contact your Yamaha dealer.
Those who have little knowledge and skill concerning servicing are request- ed not to undertake inspection, adjustment, disassembly, or reassembly only by reference to this manual. Remove: 1. Crankshaft end accessing screw Refer to removal section. Timing chain tensioner cap bolt Refer to removal section. Timing chain tensioner Refer to removal section. Gasket Refer to removal section. Remove: Cam lobes length: 1. Camshaft-to-cap clear- ance: 0.
With the rod fully wound and the chain tensioner UP mark "a" fac- ing upward, install the gasket "1", the timing chain tensioner "2", and the gasket "3", and tighten the bolt "4" to the specified torque. Bolt timing chain ten- sioner : 10 Nm 1.
Cylinder head Cylinder head gasket Timing chain guide intake side Coolant temperature sensor Oil check bolt Oil passage plug Tighten the cylinder head bolts to 30 Nm 3. Tighten the bolts to the specified 1. Valve lifter Refer to removal section. Adjusting pad Refer to removal section. Valve cotter Refer to removal section. Intake: 1. Install: 1. Install the valve cotters by compress- ing the valve spring with the valve Free length valve spring compressor "1" Piston pin Refer to removal section.
Piston Refer to removal section. Position: 2. Insert a ring into the cylinder and a. Measure the outside diameter push it approximately 40mm 1. Clutch cable Disconnect at engine side. Clutch cover Gasket Clutch spring Pressure plate Clutch boss Refer to removal section. Thrust washer Primary driven gear Push lever shaft Measure: 1. Install: 7. Washer Refer to removal section. Impeller shaft Refer to removal section. Oil seal 1 Refer to removal section. Oil seal 2 Refer to removal section. Bearing Refer to removal section.
Nut balancer Refer to removal section. Nut primary drive gear Refer to removal section. Straighten the lock washer tab. Kick idle gear Kick shaft assembly Refer to removal section. Spring guide Torsion spring Ratchet wheel Kick gear
0コメント